PROBLEME MCP el PROSIM737

PMDG / Level-D / Dreamfleet, etc...

PROBLEME MCP el PROSIM737

Messagede jeros57600 » Mer 30 Jan 2013 13:23

salut !

JE VIENS D’ACHETER PROSIM 737 FULL VERSION ET J’AI RENCONTRE UN PROBLEME POUR LE FONCTIONNEMENT DU MCP DE CHEZ CP FLIGHT, QUI DESORMAIS A ETE RESOLU.
EN CONSEQUENCES JE TIENS A FAIRE PARTAGER L’INFORMATION POUR PEUT ETRE AIDER CERTAINS QUI RENCONTRE LE MEME PROB.
APRES AVOIR INSTALLE LE TOUT, J‘ AI TESTE LE MCP CP FLIGHT VERSION EL AVEC LES DEUX EFIS VERSION EL EGALEMENT.
DANS LE LOGICIEL DE TEST CP FLIGHT AUCUN PROBLEME MAIS DES QUE JE CONNECTAIS LE PROSIM MCP, UN ONGLET RESTAIT ROUGE «HARDWARE NOT CONNECTED » ALORS QUE J’AVAIS BIEN CONNECTE LE BON PORT COM...
J’AI CONTACTE PROSIM ET CP FLIGHT QUI M’ONT SIMPLEMENT EXPLIQUE QUE DANS
PROSIM / CONFIG/ DRIVER
IL NE FALAIT PAS SELECTIONNER DE PORT COM, CONTRAIREMENT AUX VERSIONS MCP PRO…
VOYEZ LEURS REPONSES.
AMICALEMENT
http://jeros57600.skyrock.com/

-----------------REPONSE DE CP FLIGHT--------
You have to select the com port only in the config of the MCP, not in the config driver version. See the attachment
Best Regards / paolo / CPflight

-----------REPONSE DE PROSIM-------------------------
Using CPFlight hardware other than the CPFlight MCP/EFIS
CPFlight hardware is connected to each other with black CPFlight link cables. One of the devices serves as the host and is connected to the computer. This is usually the CPFlight MCP device, but CPFlight also sells panels that have a direct connection to the computer. These panels can be used when you have no CPFlight MCP.
It is important to check what CPFlight device connects to your computer. This can be either the CPFlight MCP, or some other CPFlight device. Then, choose one of the following:
Your CPFlight hardware is connected through the CPFlight MCP
Configure ProSimMCP with the right COM port.
Open the “drivers” tab in the ProSim737 configuration screen and select “CPFlight boards through MCP”
Your CPFlight hardware is connected though some panel other than the CPFlight MCP
Only configure ProSim737. Open the “drivers” tab in the configuration screen and select the correct COM port in the line “CPFlight boards direct connection”
All CPFlight panels and boards have specifically labeled switches, buttons and connectors. Because of this, it is not needed to further specify what switches and indicators should be connected where in the ProSim737 configuration screens. To use CPFlight boards, you only need to perform the steps mentioned above and leave all switches and indicators that the boards should control to “[Not connected]”. ProSim737 will automatically control the correct switches when they are received from the CPFlight hardware.
----------------------------------------------------------------------------
jeros57600
 
Messages: 26
Inscription: 3/05/09

Re: PROBLEME MCP el PROSIM737

Messagede stevelep » Mer 30 Jan 2013 13:47

Merci pour l'info qui sera sûrement utile à d'autres membres applaublanc

BOB, le modérateur

PS: Ecris tes prochains messages en minuscule stp, c'est plus facile pour la lecture
Avatar de l’utilisateur
stevelep
Administrateur du site
 
Messages: 2075
Inscription: 27/03/09
Localisation: LSGN Neuchâtel, Suisse


Retourner vers Add-Ons d'avions pour nos cockpits





Qui est en ligne

Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 1 invité