aircockpit.com

Echange et partage entre créateurs et réalisateurs de simulateurs de vol.
http://aircockpit.com/

sioc 4.0 window7 et fsx galère

http://aircockpit.com/viewtopic.php?f=66&t=3290

Page 1 sur 1

sioc 4.0 window7 et fsx galère

MessagePosté: Ven 15 Juin 2012 17:11
de g'déon
bonjour les copains,
je viens d'acquerrir un overhead panel qui fonctionne sous open cocpkit donc sioc....
je n'y entend rien donc je demande de l'aide...
donc pour resumer j'utilise prosim (license enregistree)+fsx +avion de jetstream+fsuipc (licence enregistré)+sioc4.0 tout cela sous window7 64bits.
lorsque je branche :
sioc+controlador en mode test tout cela fonctionne plutot bien en mode test display, servos inter ...
lorsque je branche fsx puis sioc puis prosim et prosimpanel et bien sur l'overhead que neni rien ne se passe pas meme une petite led qui s'allume.
pour le matos sur l'overheadpanel :
1 carte usb extension alimentée en 5v
2 cartes master (A et B) sur j1 et j2 de l'usb extention alimentée en 5v chacune
2 cartes displays connectée sur j4 master A
au nivau du script sioc.siss et sioc.ini je vous joins une copie et un screen de sioc en marche avec fsx et prosim
fichier sioc.ini
Code: Tout sélectionner
[[ fichero de configuracion para el SIOC ver. 4.0 ]
[ Configuration file for SIOC ]


[************** SIOC ***************]

[ Nombre asignado al SIOC ]
[ SIOC name ]
Name=Main

[ Puerto del servidor IOCP ]
[ IOCP port ]
IOCP_port=8092

[ Tiempo de respuesta máximo de los paquetes IOCP ]
[ IOCP Timeout ]
IOCP_timeout=4000

[ Arranque minimizado en la barra ]
[ Start minimized in tray ]
Minimized=No

[ Retraso necesario para las variables toggles (Project Magenta)]
[ Deley needed for var. toggles (Project Magenta) ]
toggle_delay=20

[ Fichero de configuracion ]
[ Configuration File ]
CONFIG_FILE=.\siocHOVD.ssi

[************** MONITOR MODULE ***************]

[ Desabilitar monitorizacion remota del SIOC ]
[ Remote monitor disable mode yes/no ]
Monitor_disable=No

[ Refresco broadcast monitor (en segundos) ]
[ Broadcast monitor time (seconds) ]
Monitor_time=2


[************** IOCARDS MODULE ***************]

[ Desactivar el módulo de las IOCards ]
[ Disable IOCards module ]
IOCard_disable=No

[ Divisor de frecuencia para los ejes analogicos (1-999). Retarda la entrega de valores. ]
[ Frequency divisor for delay the analogic axes. (1-999)]
Divisor_AD=10

[------------- CARDS CONFIG -------------]

[ IOCard Master ]
[...............]

[ Spanish : ]

[ MASTER=(Indice device),(Tipo),(Número de tarjetas),(Número device) ]

[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]

[ tipo = 0 : Emulador de Master Card // OBSOLETO ]
[ tipo = 1 : Tarjeta Master conectada al puerto paralelo directamente // OBSOLETO ]
[ tipo = 2 : Tarjeta Master conectada al puerto paralelo mediante cable de compatibilidad // OBSOLETO ]
[ tipo = 3 : Placa de expansión por puerto paralelo // OBSOLETO ]
[ tipo = 4 : Tarjeta USBExpansion usada ]
[ tipo = 5 : Modulo MCP de Opencockpits ]
[ tipo = 6 : Tarjeta USBOutputs ]
[ tipo = 7 : Modulo EFIS de Opencockpits ]
[ tipo = 8 : Modulo Radio COM de Opencockpits ]
[ tipo = 9 : Modulo Radio NAV de Opencockpits ]
[ tipo = 10 : Modulo Radio ADF de Opencockpits ]
[ tipo = 11 : Modulo Radio ATC de Opencockpits ]
[ tipo = 12 : Modulo Radio Airbus RMP de Opencockpits ]


[ Número de tarjetas = Número de placas Master usadas, 1 a 4 para uso de placas de expansión, 1 para conexión de placa Master directa o del Emulador ]

[ Número de device = 0 en el caso del Emulador o primera tarjeta USB detectada, Dirección del puerto paralelo (por ejemplo $0378), o número de dispositivo USB ]


[ Un ejemplo de 2 USBExpansion conectadas con 3 y 2 placas Master ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]

[ Un ejemplo de conexión a simulador ]
[ MASTER=0,0,1,0 ]


[ English : ]

[ MASTER=(Device index),(Type),(Number of cards),(Device number) ]

[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]

[ type = 0 : Master Card Emulator // OBSOLETE ]
[ type = 1 : Master Card connected directly to parallel port // OBSOLETE ]
[ type = 2 : Master Card connected throught compatibility cable to parallel port //OBSOLETE]
[ type = 3 : Expansion Card connected throught parallel port //OBSOLETE ]
[ type = 4 : USBExpansion Card used ]
[ type = 5 : Opencockpits MCP module ]
[ type = 6 : USBOutputs Card used ]
[ type = 7 : EFIS module ]
[ type = 8 : Radio COM module ]
[ type = 9 : Radio NAV module ]
[ type = 10 : Radio ADF module ]
[ type = 11 : Radio ATC module ]
[ type = 12 : Radio RMP Airbus module ]

[ Number of Cards = Master cards connecteds, 1 to 4 for expansion cards, 1 for a Master card directly connected or Emulator ]

[ Number of device = 0 for Emulator or first USB card detected, parallel port address, device number for specifies USBexpansion card ]

[ For example, two USBExpansion cards connected with 3 and 2 Master cards used ]
[ MASTER=0,4,3,22 ]
[ MASTER=1,4,2,24 ]

[ For example, use of Master card emulator ]
[ MASTER=0,0,1,0 ]

[ Use the first USBExpansion card connected with only one Master Card attached ]
[ Esta definición es para usar la primera tarjeta USBExpansion que se encuentre instalada que además llevará conectada una placa Master ]

[MASTER=3,6,1,252]
[MASTER=0,4,1,0]

MASTER=40,4,2,47
USBServos=60,29


[ Others Cards / Otras tarjetas ]
[...............................]

[ Spanish : ]

[ Nombre_de_tarjeta=(Indice device),(Número device) ]

[ Indice Device: Índice usado en la variable SIOC como device, para indicar a que tarjeta se hace referencia ]
[ Se usa 0 en el caso de que sólo haya una tarjeta y no se tenga en cuenta el número de device, por defecto un script en SIOC cuando no se pone parámetro DEVICE, se hace referencia al índice 0]

[ Número de device = 0 para usar primera tarjeta USB de este tipo detectada ó número de dispositivo USB ]


[ English : ]

[ Name_of_card=(Device index),(Device number) ]

[ Device index : Index used in SIOC variable like device, this is the card used for SIOC sentence ]
[ Use 0 for only one card, for this value you not need specify Device number. If you not use DEVICE parameter in a definition in SIOC script, the default index used is 0]

[ Number of device = 0 for first USB card of this type detected, or device number for a specifies device ]

[ Ejemplo de dos USBServos en indices 0 y 1, y números de devices 17 y 23 ]
[ Example of two USBServos for index 0 and 1, and device number 17 and 23 ]

[ USBServos=0,17 ]
[ USBServos=1,23 ]


USBStepper=0,0
USBKeys=0,0
USBServos=0,0
USBRelays=0,0
USBDCmotor=0,0

[ Para los ejes analógicos se usan los números de devices de las tarjetas donde están alojados ]
[ For analogic axles, you use the device number of cards what allow the axles ]

USBAnalogic=0,0


[************** FSUIPC MODULE ***************]

[ Desabilitar lectura de las FSUIPC ]
[ FSUIPC disable mode yes/no ]
FSUipcdisable=No

[ Refresco recepción FSUIPC ]
[ FSUIPC refresh ]
FSUipcRefresh=50


[************** IOCP CLIENTS MODULES ***************]

[ Retraso para inicializacion una vez conectado el cliente en milisegundos ]
[ Delay for initialization when client has been connected in mseconds ]
IOCPini_delay=3000

[************** IOCP CLIENT MODULE #0 ***************]

[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient0_disable=No

[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient0_host=localhost

[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient0_port=8099


[************** IOCP CLIENT MODULE #1 ***************]

[ Desactivar el módulo cliente IOCP ]
[ Disable IOCP client module ]
IOCPclient1_disable=Yes

[ IP del servidor donde debe de conectar el cliente ]
[ IOCP client host name ]
IOCPclient1_host=localhost

[ Puerto de envio del protocolo IOCP cliente ]
[ IOCP client port ]
IOCPclient1_port=8099


[************** SOUND MODULE ***************]

[ Ficheros de sonido ]
[ Sound Files ]

[ Desactivar el módulo de sonido ]
[ Disable Sound module ]
Sound_disable=NO

[ Volumen general de los sonidos 0-100 ]
[ Master Volume 0-100 ]
Volume=100


[ put '*' first filename for loop Sound ]
[ anteponer '*' en el fichero para bucle continuo de sonido]

[ Sound=wav_file,frequency,volume,pan ]
[ frequency=100 to 100000 0=original -1=current ]
[ volume=0 to 100, -1=current ]
[ pan=-100 (left) to +100 (right) 0=center -1=current ]

[ Sound=Fichero_wav,frecuencia,volumen,balance ]
[ frecuencia=100 hasta 100000 0=original -1=Por defecto ]
[ volumen=0 hasta 100 -1=Volumen por defecto ]
[ balance=-100 (Izquierda) hasta +100 (Derecha) 0=centro -1=Por defecto ]

[ #1 ]
Sound=APDis.wav,-1,-1,-1

[ #2 ]
Sound=*outermk.wav,-1,-1,-1

[ #3 ]
Sound=*hello.wav

[************** KEYBOARD EMULATOR MODULE ***************]

[ Nombre exacto de la ventana donde se enviarán las teclas ]
[ Name of window for key send ]
[window = "Project Magenta Glass Cockpit - Build 396" ]

window =a.txt - Bloc de notas


[ Asignación de teclas ]
[ assign youe keys ]

#1=\B\A
#2=B
#3=C
#4=D
#5=E
#6=F
#7=G
#8=H
#9=I
#10=J
#11=K
#12=L
#13=M
#14=N
#15=O
#16=P
#17=Q
#18=R
#19=S
#20=T
#21=U
#22=V
#23=W
#24=X
#25=Y
#26=Z
#27=1
#28=2
#29=3
#30=4
#31=5
#32=6
#33=7
#34=8
#35=9
#36=0
#37=<
#38=,
#39=.
#40=-
#41=*
#42=+
#43=//
#44=/0
#45=/1
#46=/A
#47=
#48=
#49=
#50=
#51=
#52=
#53=
#54=
#55=
#56=
#57=
#58=
#59=
#60=
#61=
#62=
#63=
#64=
#65=
#66=
#67=
#68=
#69=
#70=
#71=
#72=
#73=
#74=
#75=
#76=
#77=
#78=
#79=
#80=
#81=
#82=
#83=
#84=
#85=
#86=
#87=
#88=<a
#200=<b

[ End of File ]
]

fichier sioc ssi


[// *****************************************************************************
// * Config_SIOC ver 4.01   -     By Manuel Velez    -    http://www.opencockpits.com
// *****************************************************************************
// * FileName : sioc ovdhead.txt
// * Date : 15/06/2012



Var 3029, name LED_FCRUDA_LP, Link IOCARD_OUT, Device 40, Output 92     // FC rudder a low pressure

Var 3031, name LED_FCRUDB_LP, Link IOCARD_OUT, Device 40, Output 93     // FC rudder b low pressure

Var 3033, name LED_FC_DIFP, Link IOCARD_OUT, Device 40, Output 94     // FC feel diff pressure

Var 3035, name LED_BAT_DIS, Link IOCARD_OUT, Device 40, Output 95     // BAT elec dicharge

Var 3037, name LED_TR_UNIT, Link IOCARD_OUT, Device 40, Output 96     // TR unit

Var 3039, name LED_ENG1_DR, Link IOCARD_OUT, Device 40, Output 97     // Drive eng1

Var 3041, name LED_STDPW_O, Link IOCARD_OUT, Device 40, Output 98     // Stdby power off

Var 3043, name LED_ENG2_DR, Link IOCARD_OUT, Device 40, Output 99     // Drive eng2

Var 3045, name LED_GND_PWR, Link IOCARD_OUT, Device 40, Output 100     // Ground power

Var 3047, name LED_XFER_G2, Link IOCARD_OUT, Device 40, Output 101     // Transfer bus off GEN2

Var 3049, name LED_SRC_G2, Link IOCARD_OUT, Device 40, Output 102     // Source off GEN2

Var 3051, name LED_XFER_G1, Link IOCARD_OUT, Device 40, Output 103     // Transfer bus off GEN1

Var 3053, name LED_SRC_G1, Link IOCARD_OUT, Device 40, Output 104     // Source off GEN1

Var 3055, name LED_GOFF_G1, Link IOCARD_OUT, Device 40, Output 105     // Gen off GEN1

Var 3057, name LED_GOFF_A, Link IOCARD_OUT, Device 40, Output 106     // APU Gen off

Var 3059, name LED_GOFF_G2, Link IOCARD_OUT, Device 40, Output 107     // Gen off GEN2

Var 3061, name LED_MAINT_A, Link IOCARD_OUT, Device 40, Output 108     // APU MAINT

Var 3063, name LED_APU_LP, Link IOCARD_OUT, Device 40, Output 109     // APU low pressure

Var 3065, name LED_GNDC, Link IOCARD_OUT, Device 40, Output 110     // GND call

Var 3067, name LED_EE_NA, Link IOCARD_OUT, Device 40, Output 111     // Emergency Exit not armed

Var 3069, name LED_EC_L, Link IOCARD_OUT, Device 40, Output 112     // Equip cooling l off

Var 3071, name LED_EC_R, Link IOCARD_OUT, Device 40, Output 176     // Equip cooling r off

Var 3073, name LED_MANUAL, Link IOCARD_OUT, Device 40, Output 139     // Press manual

Var 3075, name LED_ALTN, Link IOCARD_OUT, Device 40, Output 140     // Press altn

Var 3077, name LED_DBLEED, Link IOCARD_OUT, Device 40, Output 141     // Dual bleed

Var 3079, name LED_RD_R, Link IOCARD_OUT, Device 40, Output 142     // Right ram door full open

Var 3081, name LED_RD_L, Link IOCARD_OUT, Device 40, Output 143     // Left ram door full open

Var 3083, name LED_WH_LS_ON, Link IOCARD_OUT, Device 40, Output 144     // Left side ON

Var 3085, name LED_WH_LF_ON, Link IOCARD_OUT, Device 40, Output 145     // Left fwd ON

Var 3087, name LED_WH_RF_ON, Link IOCARD_OUT, Device 40, Output 146     // Right fwd ON

Var 3089, name LED_WH_RS_ON, Link IOCARD_OUT, Device 40, Output 147     // Right side ON

Var 3091, name LED_WH_RF_OV, Link IOCARD_OUT, Device 40, Output 148     // Right fwd overheat

Var 3093, name LED_WH_LS_OV, Link IOCARD_OUT, Device 40, Output 149     // Left side overhead

Var 3095, name LED_WH_LF_OV, Link IOCARD_OUT, Device 40, Output 150     // Left fwd overheat

Var 3097, name LED_WH_RS_OV, Link IOCARD_OUT, Device 40, Output 151     // Right side overheat

Var 3099, name LED_LELEV_PIT, Link IOCARD_OUT, Device 40, Output 152     // L ELEV PITOT

Var 3101, name LED_CAPT_PIT, Link IOCARD_OUT, Device 40, Output 153     // Capt PITOT

Var 3103, name LED_RELEV_PIT, Link IOCARD_OUT, Device 40, Output 154     // L ELEV PITOT

Var 3105, name LED_TEMP_PRO, Link IOCARD_OUT, Device 40, Output 155     // Temp probe

Var 3107, name LED_FO_PIT, Link IOCARD_OUT, Device 40, Output 156     // F/O PITOT

Var 3109, name LED_LALPHA_VAN, Link IOCARD_OUT, Device 40, Output 157     // L ALPHA PITOT

Var 3111, name LED_RALPHA_VAN, Link IOCARD_OUT, Device 40, Output 158     // R ALPHA PITOT

Var 3113, name LED_AUX_PIT, Link IOCARD_OUT, Device 40, Output 159     // AUX PITOT

Var 3115, name LED_ELE2_LP, Link IOCARD_OUT, Device 40, Output 160     // Hydr elec 2 low pressure

Var 3117, name LED_EN1_LP, Link IOCARD_OUT, Device 40, Output 161     // Hydr engine 1 low pressure

Var 3119, name LED_EN2_CVO_B, Link IOCARD_OUT, Device 40, Output 162     // Cowl valve open engine 2 Bright

Var 3121, name LED_EN2_CVO_D, Link IOCARD_OUT, Device 40, Output 163     // Cowl valve open engine 2 Dimmed

Var 3120, name fs_en2_cvo
{
  IF &fs_en2_cvo = 1
  {
    &LED_EN2_CVO_D = 1   
    &LED_EN2_CVO_B = 0   
  }
  IF &fs_en2_cvo = 2
  {
    &LED_EN2_CVO_B = 1   
    &LED_EN2_CVO_D = 0   
  }
  IF &fs_en2_cvo = 0
  {
    &LED_EN2_CVO_B = 0   
    &LED_EN2_CVO_D = 0   
  }
}

Var 3122, name LED_EN1_CVO_B, Link IOCARD_OUT, Device 40, Output 164     // Cowl valve open engine 1 Bright

Var 3124, name LED_EN1_CVO_D, Link IOCARD_OUT, Device 40, Output 165     // Cowl valve open engine 1 Dimmed

Var 3123, name fs_en1_cvo
{
  IF &fs_en1_cvo = 1
  {
    &LED_EN1_CVO_D = 1   
    &LED_EN1_CVO_B = 0   
  }
  IF &fs_en1_cvo = 2
  {
    &LED_EN1_CVO_B = 1   
    &LED_EN1_CVO_D = 0   
  }
  IF &fs_en1_cvo = 0
  {
    &LED_EN1_CVO_B = 0   
    &LED_EN1_CVO_D = 0   
  }
}

Var 3125, name LED_WVALV_R_B, Link IOCARD_OUT, Device 40, Output 166     // Wing valve open right Bright

Var 3127, name LED_WVALV_R_D, Link IOCARD_OUT, Device 40, Output 167     // Wing valve open right Dimmed

Var 3126, name fs_wvalv_r
{
  IF &fs_wvalv_r = 1
  {
    &LED_WVALV_R_D = 1   
    &LED_WVALV_R_B = 0   
  }
  IF &fs_wvalv_r = 2
  {
    &LED_WVALV_R_B = 1   
    &LED_WVALV_R_D = 0   
  }
  IF &fs_wvalv_r = 0
  {
    &LED_WVALV_R_B = 0   
    &LED_WVALV_R_D = 0   
  }
}

Var 3128, name LED_WVALV_L_B, Link IOCARD_OUT, Device 40, Output 168     // Wing valve open left Bright

Var 3130, name LED_WVALV_L_D, Link IOCARD_OUT, Device 40, Output 169     // Wing valve open left Dimmed

Var 3129, name fs_wvalv_l
{
  IF &fs_wvalv_l = 1
  {
    &LED_WVALV_L_D = 1   
    &LED_WVALV_L_B = 0   
  }
  IF &fs_wvalv_l = 2
  {
    &LED_WVALV_L_B = 1   
    &LED_WVALV_L_D = 0   
  }
  IF &fs_wvalv_l = 0
  {
    &LED_WVALV_L_B = 0   
    &LED_WVALV_L_D = 0   
  }
}

Var 3131, name LED_EN2_LP, Link IOCARD_OUT, Device 40, Output 170     // Hydr engine 2 low pressure

Var 3133, name LED_ELE1_LP, Link IOCARD_OUT, Device 40, Output 171     // Hydr elec 1 low pressure

Var 3135, name LED_FWD_CAR, Link IOCARD_OUT, Device 40, Output 172     // Fwd cargo

Var 3137, name LED_AFT_CAR, Link IOCARD_OUT, Device 40, Output 173     // Aft cargo

Var 3139, name LED_AFT_ENT, Link IOCARD_OUT, Device 40, Output 174     // Aft entry

Var 3141, name LED_FWD_ENT, Link IOCARD_OUT, Device 40, Output 175     // Aft entry

Var 3180, name DP_DC_AMP, Link IOCARD_DISPLAY, Device 40, Digit 89, Numbers 2     // DC AMP on display card

Var 3182, name DP_DC_VOLT, Link IOCARD_DISPLAY, Device 40, Digit 92, Numbers 2     // DC VOLT on display card

Var 3184, name DP_CPS_FRQ, Link IOCARD_DISPLAY, Device 40, Digit 86, Numbers 3     // CPS FREQ

Var 3186, name DP_AC_AMP, Link IOCARD_DISPLAY, Device 40, Digit 83, Numbers 2     // AC AMP on display card

Var 3188, name DP_AC_VOLT, Link IOCARD_DISPLAY, Device 40, Digit 80, Numbers 3     // AC VOLT on display card

Var 3190, name DP_FLT_ALT, Link IOCARD_DISPLAY, Device 40, Digit 64, Numbers 5     // Flight alt on display card

Var 3192, name DP_LAND_ALT, Link IOCARD_DISPLAY, Device 40, Digit 69, Numbers 5     // Land alt on display card

Var 3200, Link IOCARD_SW, Device 40, Input 108     // CROSS-FEED

Var 3201, Link IOCARD_SW, Device 40, Input 109     // FWD PUMP ENG1 ON

Var 3202, Link IOCARD_SW, Device 40, Input 110     // AFT PUMP ENG1 ON

Var 3203, Link IOCARD_SW, Device 40, Input 111     // AFT ENG2 ON

Var 3204, Link IOCARD_SW, Device 40, Input 112     // FWD ENG2 ON

Var 3205, Link IOCARD_SW, Device 40, Input 113     // TAXI LIGHTS

Var 3206, Link IOCARD_SW, Device 40, Input 114     // YAW DAMPER

Var 3207, Link IOCARD_SW, Device 40, Input 115     // CTR L FUEL PUMP

Var 3208, Link IOCARD_SW, Device 40, Input 116     // CTR R FUEL PUMP

Var 3209, name FS_STGND_1, Link IOCARD_SW, Device 40, Input 117     // ENG1 START GND

Var 3210, name FS_STGND_2, Link IOCARD_SW, Device 40, Input 118     // ENG2 START GND

Var 3211, Link IOCARD_SW, Device 40, Input 119     // ENG2 START CONT

Var 3212, Link IOCARD_SW, Device 40, Input 120

Var 3213, Link IOCARD_SW, Device 40, Input 121     // ENG2 START FLT

Var 3214, Link IOCARD_SW, Device 40, Input 122     // LOGO LIGHT

Var 3215, Link IOCARD_SW, Device 40, Input 123     // ENG1 START CONT

Var 3216, Link IOCARD_SW, Device 40, Input 124     // ENG1 START FLT

Var 3217, Link IOCARD_SW, Device 40, Input 125

Var 3218, Link IOCARD_SW, Device 40, Input 126     // APU START START

Var 3219, Link IOCARD_SW, Device 40, Input 127     // LANDING LIGHTS

Var 3220, Link IOCARD_SW, Device 40, Input 128     // STROBE LIGHTS

Var 3221, Link IOCARD_SW, Device 40, Input 129     // ANTICOL LIGHTS

Var 3222, Link IOCARD_SW, Device 40, Input 130     // NAVIGATION LIGHTS

Var 3223, Link IOCARD_SW, Device 40, Input 131     // APU START OFF

Var 3224, Link IOCARD_SW, Device 40, Input 132     // PRESSURE MANUAL

Var 3225, Link IOCARD_SW, Device 40, Input 133     // PRESSURE AUTO

Var 3226, Link IOCARD_SW, Device 40, Input 134     // WING LIGHTS

Var 3227, Link IOCARD_SW, Device 40, Input 135     // GEN 1 OFF

Var 3228, Link IOCARD_SW, Device 40, Input 136     // GEN 2 ON

Var 3229, Link IOCARD_SW, Device 40, Input 137     // GEN 2 OFF

Var 3230, Link IOCARD_SW, Device 40, Input 138     // APU 2 ON

Var 3231, Link IOCARD_SW, Device 40, Input 139     // APU 2 OFF

Var 3232, Link IOCARD_SW, Device 40, Input 140     // BUS TRANSFER

Var 3233, Link IOCARD_SW, Device 40, Input 141     // GEN 1 ON

Var 3234, Link IOCARD_SW, Device 40, Input 142     // APU 1 ON

Var 3235, Link IOCARD_SW, Device 40, Input 143     // APU 1 OFF

Var 3236, Link IOCARD_SW, Device 40, Input 144     // DRIVE 2 DISCONNECT

Var 3237, Link IOCARD_SW, Device 40, Input 145     // GRD POWER ON

Var 3238, Link IOCARD_SW, Device 40, Input 146     // WIPER L OFF

Var 3239, Link IOCARD_SW, Device 40, Input 147     // WIPER L LOW

Var 3240, Link IOCARD_SW, Device 40, Input 148     // WIPER L HIGH

Var 3241, Link IOCARD_SW, Device 40, Input 149     // GRD POWER OFF

Var 3242, Link IOCARD_SW, Device 40, Input 150     // DRIVE 1 DISCONNECT

Var 3243, Link IOCARD_SW, Device 40, Input 151     // STANDBY POWER auto

Var 3244, Link IOCARD_SW, Device 40, Input 152     // stby powr bat

Var 3245, Link IOCARD_SW, Device 40, Input 153     // EMERGENCY LIGHTS OFF

Var 3246, Link IOCARD_SW, Device 40, Input 154     // GND CALL

Var 3247, Link IOCARD_SW, Device 40, Input 155     // SEAT BELTS on

Var 3248, Link IOCARD_SW, Device 40, Input 156     // NO SMOKING on

Var 3249, Link IOCARD_SW, Device 40, Input 157     // setbelts off

Var 3250, Link IOCARD_SW, Device 40, Input 158     // EQUIP COOLING EXHAUST NORMAL

Var 3251, Link IOCARD_SW, Device 40, Input 159     // EQUIP COOLING SUPPLY NORMAL

Var 3252, Link IOCARD_SW, Device 40, Input 160     // LEFT SIDE WINDOW HEAT

Var 3253, Link IOCARD_SW, Device 40, Input 161     // no smoking off

Var 3254, Link IOCARD_SW, Device 40, Input 162     // R PACK HIGH

Var 3255, Link IOCARD_SW, Device 40, Input 163     // VALVE CLOSE

Var 3256, Link IOCARD_SW, Device 40, Input 164     // VALVE OPEN

Var 3257, Link IOCARD_SW, Device 40, Input 165     // L PACK HIGH

Var 3258, Link IOCARD_SW, Device 40, Input 166     // BLEED AIR APU

Var 3259, Link IOCARD_SW, Device 40, Input 167     // L PACK OFF

Var 3260, Link IOCARD_SW, Device 40, Input 168     // BLEED AIR ENG 1

Var 3261, Link IOCARD_SW, Device 40, Input 169     // BLEED AIR ENG 2

Var 3262, Link IOCARD_SW, Device 40, Input 170     // R PACK OFF

Var 3263, Link IOCARD_SW, Device 40, Input 171     // R RECIRC FAN AUTO

Var 3264, Link IOCARD_SW, Device 40, Input 172     // LEFT FWD WINDOW HEAT

Var 3265, Link IOCARD_SW, Device 40, Input 173     // RIGHT FWD WINDOW HEAT

Var 3266, Link IOCARD_SW, Device 40, Input 174     // WINDOW HEAT PROBE A

Var 3267, Link IOCARD_SW, Device 40, Input 175     // WINDOW HEAT POWER TEST

Var 3268, Link IOCARD_SW, Device 40, Input 176     // L RECIRC FAN AUTO

Var 3269, Link IOCARD_SW, Device 40, Input 177     // RIGHT SIDE WINDOW HEAT

Var 3270, Link IOCARD_SW, Device 40, Input 178     // WINDOW HEAT PROBE B

Var 3271, Link IOCARD_SW, Device 40, Input 179     // WINDOW HEAT OVHT

Var 3272, Link IOCARD_SW, Device 40, Input 180     // HYD PUMP ELEC 1

Var 3303, Link IOCARD_SW, Device 40, Input 181     // RIGHT ENG ANTIICE

Var 3274, Link IOCARD_SW, Device 40, Input 100     // GALLEY ON

Var 3275, Link IOCARD_SW, Device 40, Input 183     // HYD PUMP ENG 1

Var 3276, Link IOCARD_SW, Device 40, Input 184     // BATTERIE SWITCH

Var 3277, Link IOCARD_SW, Device 40, Input 185     // HYD PUMP ENG 2

Var 3278, Link IOCARD_SW, Device 40, Input 186     // WING ANTIICE

Var 3279, Link IOCARD_SW, Device 40, Input 187     // HYD PUMP ELEC 2

Var 3280, Link IOCARD_SW, Device 40, Input 188     // LEFT ENG ANTIICE

Var 3281, Link IOCARD_SW, Device 40, Input 189     // BAT ROT STDBY POWER

Var 3282, Link IOCARD_SW, Device 40, Input 190     // BAT ROT BAT

Var 3283, Link IOCARD_SW, Device 40, Input 191     // BAT ROT TR1

Var 3284, Link IOCARD_SW, Device 40, Input 192     // BAT ROT TR2

Var 3285, Link IOCARD_SW, Device 40, Input 193     // BAT ROT TR3

Var 3286, Link IOCARD_SW, Device 40, Input 194     // BAT ROT TEST

Var 3287, Link IOCARD_SW, Device 40, Input 195     // BAT ROT BAT BUS

Var 3288, Link IOCARD_SW, Device 40, Input 196     // FLT CONTROL A STY

Var 3289, Link IOCARD_SW, Device 40, Input 197     // FLT CONTROL A ON

Var 3290, Link IOCARD_SW, Device 40, Input 198     // PWR ROT STDBY PWR

Var 3291, Link IOCARD_SW, Device 40, Input 199     // PWR ROT GEN1

Var 3292, Link IOCARD_SW, Device 40, Input 200     // PWR ROT APU GEN

Var 3293, Link IOCARD_SW, Device 40, Input 201     // PWR ROT GEN2

Var 3294, Link IOCARD_SW, Device 40, Input 202     // PWR ROT INV

Var 3295, Link IOCARD_SW, Device 40, Input 203     // PWR ROT TEST

Var 3296, Link IOCARD_SW, Device 40, Input 204     // ALTERNATE FLAPS ARMED

Var 3297, Link IOCARD_SW, Device 40, Input 205     // FLT CONTROL B STY

Var 3298, Link IOCARD_SW, Device 40, Input 206     // FLT CONTROL B ON

Var 3299, Link IOCARD_SW, Device 40, Input 213     // ALTERNATE FLAPS UP

Var 3300, Link IOCARD_SW, Device 40, Input 215     // ALTERNATE FLAPS DOWN

Var 3301, Link IOCARD_SW, Device 40, Input 214     // SPOILER A ON

Var 3302, Link IOCARD_SW, Device 40, Input 209     // SPOILER B ON

Var 3304, Link IOCARD_SW, Device 40, Input 212     // TRIM AIR

Var 3311, name FLTALT_ENCODER, Link IOCARD_ENCODER, Device 40, Input 210, Aceleration 0, Type 2     // OHD FLT Alt encod
{
  L0 = &FLTALT_ENCODER * 500     // * -1 Clockwise positive
  L0 = L0 * 1
  &DP_FLT_ALT = LIMIT -1000 ,42000 ,L0
}

Var 3312, name LNDALT_ENCODER, Link IOCARD_ENCODER, Device 40, Input 207, Aceleration 0, Type 2     // OHD LND Alt encod
{
  L0 = &LNDALT_ENCODER * 500     // * -1 Clockwise positive
  L0 = L0 * 1
  &DP_LAND_ALT = LIMIT -1000 ,42000 ,L0
}

Var 3320, Link USB_SERVOS, Device 60, Output 1, PosL 1, PosC 512, PosR 1023     // APU EGT

Var 3321, Link USB_SERVOS, Device 60, Output 2, PosL 1, PosC 512, PosR 1023     // FUEL TEMP

Var 3322, Link USB_SERVOS, Device 60, Output 3, PosL 1, PosC 512, PosR 1023     // ALTI

Var 3323, Link USB_SERVOS, Device 60, Output 4, PosL 1, PosC 512, PosR 1023     // CAB ALTI

Var 3324, Link USB_SERVOS, Device 60, Output 5, PosL 1, PosC 512, PosR 1023     // DUCT PRESS RIGHT

Var 3325, Link USB_SERVOS, Device 60, Output 6, PosL 1, PosC 512, PosR 1023     // DUCT PRESS LEFT
]


sioc en marche etat des fenetres:

fenetre, iocard module:
iocard device ver: 4.0
fenetre fsuipc module
fsuipc statut ok
fsuipc version 4.600a
simulator; fsx
fenetre iocp serveur
host adress:192.168.1.18
port:8092 clients connecteds:1

fenetre device
idx=40-iocardusb.device=47
idx=60.iocard-usbservos-device=29

fenetre log
Starting SIOC
Loading SIOC config .INI :
C:\Program Files (x86)\IOCards\SIOC\sioc.ini
Initializing IOcard Module
Loading SIOC Script :
.\siocHOVD.ssi
IOCP client connected

et pourtant rien ne fonctionne sur l'overhead pas meme une lumière.
merci de votre aide
g'déon si proche du but!!!

Re: sioc 4.0 window7 et fsx galère

MessagePosté: Ven 15 Juin 2012 18:22
de Phil64
Bonjour,
Dis moi as tu fouillé du côté de Prosim avec les adressages, les paramètres, etc.... ?

Re: sioc 4.0 window7 et fsx galère

MessagePosté: Ven 15 Juin 2012 18:34
de g'déon
bonjour phil content de te voir
comme je l'ai dit je suis une vrai bi.... en sioc alors juste le mot me fait peur.
je t'envois en privés mon adresse skype si tu as du tps à me consacrer je serai heureux ?

Re: sioc 4.0 window7 et fsx galère

MessagePosté: Ven 15 Juin 2012 21:58
de stevelep
La carte USB expansion ne doit JAMAIS être alimentée au risque
de causer des dommage au PC

Le connecteur 2 pôles de cette carte n'est pas pour l'alimenter
mais c'est une source de courant pour d'autres cartes.

Il est absolument impératif de ne rien brancher sur ce connecteur

BOB

Re: sioc 4.0 window7 et fsx galère

MessagePosté: Sam 16 Juin 2012 00:19
de g'déon
bonsoir,
apres quelques bidouillages et avoir débranché l'alim de l'usb expansion (merci bob),tout semble marchait à merveille.
en fait je n'avais pas rentrée les variables dans prosim ( switch, indicator ect ect..)
merci pour votre precieuse aide et les tuyaux...
j'aurai surement besoin de vous encore pour modifier mon script sioc car il memanque pas mal de led à cabler ainsi qu'une paire de switch .
merci a bientot
phil je t'ai envoyé par mp une demande de contact merci de voir si tu es ok.
merci merci merci
Heures au format UTC + 1 heure [ Heure d’été ]
Page 1 sur 1
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/